Diy Concrete Sleepers
DIY Concrete Sleeper Wall lighting
Ultra Thin Stainless Steel bracket fits nicely between Concrete Sleepers with minimal gap.
​
Can be integrated into your new wall or Top mounted to existing Concrete Sleeper walls.
​
Full Stainless construction and Aluminium light bar with 60 degree lens for even light distribution.
​
A small groove needs to be cut with a grinder to allow the Permanent Wall Wire to pass through.
​
-
12v DC
-
Full weather rated IP67
-
Plug and Play connector fits our T-connector for waterproof run of multiple lights
-
Can be used in conjunction with our 100mm x 100mm Lights
3 Sizes Available in 2 Great Finishes
-
Brushed Stainless Steel
-
Black Powder Coat
​
​
​
​
SMALL 300mm - 1.5 Watts
MEDIUM 500mm - 3.5 Watts
LARGE 1000mm - 9 Watts
LED Light Suits a 100mm x 100mm Post
Stainless Steel bracket and aluminium light bar with 60 degree lens.
For best results your Concrete Sleeper height needs to be level with or slightly below the top of the post.
A small groove needs to be cut with a grinder to allow the wire to pass through.
Available in 3 great finishes:
-
Brushed Stainless Steel
-
Black powder coat
-
Grey powder coat
-
12V DC
-
1.5 Watts
-
Full weather rated IP67
-
Plug and play connector fits our T-connector for waterproof run of multiple lights
-
Can be used in conjunction with our Concrete Sleeper Wall lights
Example of 6 lights SET-UP
Maximum of 6 lights on a single run.
EXAMPLE OF 12 LIGHT SET-UP
T- Connector
Use this to link Extension Cables and branch off your Lights.
-
Waterproof IP67
-
Direct burial
Extension Cables
Use behind your wall to span between each light connecting to T-Connectors. . 20 AWG Slightly thicker wire to help
minimize voltage drop
-
Water Proof IP67 connectors
-
Male connectors each end
-
Direct burial
ADAPTER CABLE
If you need to join Extension cables use this Adapter cable.
This cable is also used to pass through your Concrete Sleeper Wall.
One end connects to T-connector and the other end connects to your Small , Medium or Large wall light.
20 AWG Slightly thicker wire to help minimize voltage drop
-
Waterproof IP67 connectors
-
Female threaded ends each side
-
Direct burial
Photocell-Supports MAXIMUM 120 Watts of lighting
Automatically turns on your lights at Dusk, and off at Dawn.
Connects between your LED Power supply and first light / lights.
-
Available with one or two output cables. (1 metre long)
-
Male connectors that fit directly to T-CONNECTORS.
-
1 x 1M Cable that fits directly to LINKit - cable.
-
If you need longer than 1M to reach the T-CONNECTORS then purchase the ADAPTER cables and longer EXTENSION cables.
-
High quality Aluminium enclosure with 12V DC Photoelectric cell.
-
Silicone waterproof gel filled.
-
Full weather rated IP67
​
LED Power Supply
Hi output cool running LED drivers for stable and efficient lighting.
​
Fitted with IP67 coupling that connects directly to your LINKit - CABLE
​
-
12V DC constant voltage
-
IP67
-
Not dimmable
LINKit - CABLEs
Thicker heavier duty cables for less voltage drop.
One end connects directly to LED Driver and the other end connects directly to LINKit - STEP DOWN cables.
LINKit - STEP DOWN cable (1 metre long)
You only need this cable if you are not using the PHOTOCELL.
1M long thinner cable allows you to step down from the thicker LINKit cable and connect directly to the T-CONNECTOR.
​
30 Watt Solar Panel + Lithium Battery pack
A great alternative where mains power is not available or costly to install.
Harness energy from the sun with this Solar panel and Lithium Battery Pack.
With a full charge can power your lights for around 5 hours each evening.
You can add more WATTS of lighting but the run time will be less.
-
30 Watts
-
Turns on automatically at dusk
-
Lithium Battery Pack charges throughout day
-
Has threaded Female connector suits Extension cables